This is latest KaeilOS / OpenEmbedded build test with EB9263 board by Ronetix
BUILD
Website : http://www.kaeilos.com
Build system : KaeilOS/OE 13-JUL-2009
Branch : org.openembedded.dev <-- do not use stable !
Machine : ronetix-pm9263
Image : x11-image
Command : MACHINE="ronetix-pm9263" bitbake x11-image
SHA-1 tag : 34b2c6d58596767386c3fde6e62151b026f1a103
Boot log
RomBOOT
U-Boot 2008.10-00098-gf2091f5-dirty (Dec 3 2008 - 15:18:08)
Board : Ronetix PM9263
Crystal frequency: 18.432 MHz
CPU clock : 199.066 MHz
Master clock : 99.533 MHz
USB clock : 48.055 MHz
Video memory : 0x70000000 (PSRAM)
DRAM: 64 MB
Flash: 4 MB
NAND: 256 MiB
DataFlash:AT45DB321
Nb pages: 8192
Page Size: 528
Size= 4325376 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C041FFFF
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: macb0
macb0: Starting autonegotiation...
macb0: Autonegotiation complete
macb0: link up, 100Mbps full-duplex (lpa: 0x45e1)
Hit any key to stop autoboot:
## Booting kernel from Legacy Image at 10050000 ...
Image Name: KaeilOS/2.6.28/ronetix-pm9263
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1601192 Bytes = 1.5 MB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux....................................................... done, booting the kernel.
Linux version 2.6.28 (koan@quad) (gcc version 4.2.4) #1 Wed Jun 24 10:48:05 CEST 2009
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Ronetix PM9263/BB9263
Ignoring unrecognised tag 0x54410008
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 mtdparts=physmap-flash.0:
256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),-(rootfs);nand:-(nand)
ip=192.168.3.222:192.168.3.1:192.168.3.1:255.255.255.0:PM9263:eth0:off
AT91: 160 gpio irqs in 5 banks
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty0] enabled
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61504KB available (2968K code, 248K data, 132K init)
Calibrating delay loop... 99.32 BogoMIPS (lpj=496640)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 120
io scheduler noop registered
io scheduler anticipatory registered (default)
atmel_lcdfb atmel_lcdfb.0: backlight control is not available
atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at 23940000 (mapped at ffc00000)
Console: switching to colour frame buffer device 40x30
atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00700000 (mapped at c4866000), irq 26
atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
MACB_mii_bus: probed
eth0: Atmel MACB at 0xfffbc000 irq 21 (02:ad:be:ef:01:00)
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
physmap platform flash device: 00400000 at 10000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
4 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x00040000 : "u-boot"
0x00040000-0x00050000 : "u-boot-env"
0x00050000-0x001b0000 : "kernel"
0x001b0000-0x00400000 : "rootfs"
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
AT91 NAND: 8-bit, Software ECC
Scanning device for bad blocks
Bad eraseblock 658 at 0x05240000
Bad eraseblock 792 at 0x06300000
Bad eraseblock 1603 at 0x0c860000
Creating 1 MTD partitions on "atmel_nand":
0x00000000-0x10000000 : "Partition 1"
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14)
mtd_dataflash spi0.0: AT45DB321x (4224 KBytes) pagesize 528 bytes (OTP)
atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffa8000 (irq 15)
at91_cf: irqs det #62, io #56
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 29, io mem 0x00a00000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
udc: at91_udc version 3 May 2006
mice: PS/2 mouse device common for all mice
ads7846 spi1.0: touchscreen, irq 31
input: ADS784x Touchscreen as /devices/platform/atmel_spi.1/spi1.0/input/input0
rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!
Driver for 1-wire Dallas network protocol.
Registered led device: led0
Registered led device: led1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
usb 1-1: new low speed USB device using at91_ohci and address 2
AC97C regs = FFFA0000
AC97C irq = 18
at91-ac97: codec write timeout
<4>at91-ac97: codec write timeout
<4>at91-ac97: codec write timeout
<4>at91-ac97: codec write timeout
<6>ALSA device list:
#0: Atmel AC97 Controller at 0xfffa0000, irq 18
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock
IP-Config: Complete:
device=eth0, addr=192.168.3.222, mask=255.255.255.0, gw=192.168.3.1,
host=PM9263, domain=, nis-domain=(none),
bootserver=192.168.3.1, rootserver=192.168.3.1, rootpath=
Empty flash at 0x0114b4a0 ends at 0x0114b800
Empty flash at 0x04461c14 ends at 0x04462000
Empty flash at 0x04466120 ends at 0x04466800
eth0: link up (100/Full)
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 132K
INIT: version 2.86 booting
Please wait: booting...
mount: sysfs already mounted or /sys busy
mount: according to mtab, sysfs is already mounted on /sys
udev: starting version 141
Remounting root file system...
Configuring network interfaces... done.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
hwclock: RTC_RD_TIME: Invalid or incomplete multibyte or wide character
Sat Jun 27 17:02:00 BST 2009
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Connection Manager
Starting Dropbear SSH server: dropbear.
Starting syslogd/klogd: done
Running ntpdate to synchronize clockError : Temporary failure in name resolution
.
Starting GPE display manager: gpe-dm
## ## ### ######## #### ## ####### ######
## ## ## ## ## ## ## ## ## ## ##
## ## ## ## ## ## ## ## ## ##
##### ## ## ###### ## ## ## ## ######
## ## ######### ## ## ## ## ## ##
## ## ## ## ## ## ## ## ## ## ##
## ## ## ## ######## #### ######## ####### ######(R)
KaeilOS Linux ronetix-pm9263 ttyS0
KaeilOS 2008.1-test-20081222 ronetix-pm9263 ttyS0
KaeilOS 2009.1-test-20090627 ronetix-pm9263 ttyS0
ronetix-pm9263 login:
English
Italiano
